00:00:00.030 hello welcome back in this episode the 00:00:02.89900:00:02.909 oil cooler 00:00:34.16000:00:34.170 in this episode I will be fixing this 00:00:36.72000:00:36.730 leaky oil cool before you start you 00:00:39.42000:00:39.430 should drain the engine of both oil and 00:00:41.16000:00:41.170 seawater 00:00:43.96000:00:43.970 I start with removing the seawater hose 00:00:46.45000:00:46.460 connected to the after cool 00:01:09.58000:01:09.590 after I have removed the oil filter I 00:01:12.01000:01:12.020 loosened the three bolts holding the oil 00:01:13.84000:01:13.850 filter housing do not remove the bolts 00:01:16.42000:01:16.430 yet 00:01:30.24000:01:30.250 next I unscrew the retainer holding the 00:01:32.70000:01:32.710 see water pipe in front of the pool 00:01:41.85000:01:41.860 now I remove the three bolts from the 00:01:44.22000:01:44.230 housing and remove the housing with the 00:01:46.20000:01:46.210 cooler attached there are four rubber 00:01:48.57000:01:48.580 sealant which needs to be replaced later 00:02:00.46900:02:00.479 now simply unscrew the four bolts 00:02:02.60000:02:02.610 attaching the cooler to the oil filter 00:02:04.45900:02:04.469 housing 00:02:15.49000:02:15.500 again here there are four rubber sealant 00:02:18.13000:02:18.140 which needs to be replaced 00:02:32.37000:02:32.380 now unscrew the four bolts holding the 00:02:35.05000:02:35.060 lid 00:02:52.07000:02:52.080 remove the lid and then reattach the 00:02:54.29000:02:54.300 four bolts but do not screw them all the 00:02:56.45000:02:56.460 way in leave a good centimeter on all 00:02:59.06000:02:59.070 bolts 00:03:27.36000:03:27.370 place the cooler on a solid surface 00:03:29.47900:03:29.489 resting on the four bolts 00:03:33.24000:03:33.250 if the cooler is painted in now remove 00:03:36.85000:03:36.860 the paint the sharp knife also unscrew 00:03:39.82000:03:39.830 the sink which needs to be replaced for 00:03:42.40000:03:42.410 the next part you need to be careful yet 00:03:44.35000:03:44.360 powerful you need a wooden chip about 00:03:46.66000:03:46.670 half a centimeter thick place this along 00:03:49.24000:03:49.250 the rim of the cooler insert be careful 00:03:51.91000:03:51.920 not to bend any part of the insert this 00:03:54.30900:03:54.319 is made of copper and is very soft you 00:03:56.28900:03:56.299 need to take care not to damage the 00:03:58.05900:03:58.069 insert as this can render it totally 00:04:00.40000:04:00.410 unusable it may take some hard hits but 00:04:03.30900:04:03.319 it should eventually loosen now remove 00:04:05.74000:04:05.750 the four bolts again and take out the 00:04:07.53900:04:07.549 insert 00:04:21.20000:04:21.210 remove the to erase the whole unit 00:04:24.27000:04:24.280 should now be cleaned the seawater site 00:04:26.82000:04:26.830 can be cleaned using the same mixture as 00:04:28.74000:04:28.750 I used in Episode one when I clean the 00:04:31.02000:04:31.030 heat exchanger the oil site must not be 00:04:33.83900:04:33.849 cleaned this way but instead use an 00:04:35.46000:04:35.470 alkaline cleaning agent or simply use 00:04:37.52900:04:37.539 diesel fuel rinse it thoroughly 00:04:39.45000:04:39.460 afterwards start the reassembly by 00:04:42.71900:04:42.729 inserting the new o-rings use engine oil 00:04:45.48000:04:45.490 to lubricate 00:05:38.25000:05:38.260 reattach the lid and a new gasket 00:05:43.02000:05:43.030 you 00:05:54.49000:05:54.50000:06:14.40000:06:14.410 Oh 00:06:17.62900:06:17.63900:07:52.95000:07:52.96000:08:00.54000:08:00.55000:08:29.48000:08:29.490 do not fully tighten the three bolts yet 00:08:31.81000:08:31.820 first inspect the rear of the unit to 00:08:34.37000:08:34.380 make sure that rubber sealants are 00:08:35.87000:08:35.880 placed correct any misalignment here 00:08:38.02900:08:38.039 will result in a serious oil leakage if 00:08:40.79000:08:40.800 it all looks good 00:08:41.75000:08:41.760 tighten the bolts to a torque of 40 00:08:43.61000:08:43.620 Newton meters using a torque wrench 00:08:53.82000:08:53.83000:08:59.31000:08:59.320 and that's all for this time and in the 00:09:01.56000:09:01.570 next episode I will be taking off the 00:09:03.18000:09:03.190 manifold
Office location
Engineering company LOTUS®
Russia, Ekaterinburg, Lunacharskogo street, 240/12