00:00:06.150 prior to disassembly 00:00:08.38000:00:08.390 exchanger if applicable the shroud must 00:00:11.20000:00:11.210 be removed all the bolts except bolt 00:00:15.34000:00:15.350 assemblies number one number two number 00:00:18.37000:00:18.380 three and number four should be fully 00:00:22.51000:00:22.520 loosened and removed from the heat 00:00:24.31000:00:24.320 exchanger loosened bolts one two three 00:00:29.31900:00:29.329 and four in increments of approximately 00:00:32.17000:00:32.180 one half inch per bolt in the order of 00:00:34.93000:00:34.940 one two three four until they are loose 00:00:39.85000:00:39.860 enough to be removed from the unit the 00:00:43.81000:00:43.820 movable frame is then rolled back to the 00:00:45.88000:00:45.890 support column which then exposes the 00:00:48.31000:00:48.320 plates inside the heat exchanger plates 00:00:52.02900:00:52.039 are removed one at a time in the 00:00:53.70900:00:53.719 following manner 00:00:54.45900:00:54.469 make sure the plate is lifted by a 00:00:57.00900:00:57.019 gloved hand in the port hold until the 00:00:59.59000:00:59.600 plate touches the upper guide bar the 00:01:03.52000:01:03.530 hanger is then removed and the plate is 00:01:06.01000:01:06.020 tilted and removed from the unit do not 00:01:10.30000:01:10.310 excessively bend the plate when removing 00:01:12.64000:01:12.650 this will damage the plate requiring 00:01:15.31000:01:15.320 plate replacement in the event that 00:01:17.98000:01:17.990 light cleaning or plate inspection is 00:01:20.14000:01:20.150 desired the plates can be inspected or 00:01:22.66000:01:22.670 cleaned one by one while they are 00:01:24.91000:01:24.920 hanging in the unit the UX p10 and UX p5 00:01:30.60900:01:30.619 plates are not secured by hangers they 00:01:33.70000:01:33.710 rest on the lower Guide bar since the 00:01:36.70000:01:36.710 place are small they are held in place 00:01:38.67900:01:38.689 by the hand while the moveable frame is 00:01:40.99000:01:41.000 moved to the rear the plates can then be 00:01:44.70900:01:44.719 removed by sliding each plate to the 00:01:47.13900:01:47.149 rear and allowing it to drop as it 00:01:49.20900:01:49.219 reaches the end of the lower guide bar 00:01:54.39000:01:54.400 uxp 100-series plates and all GC GX and 00:01:59.10900:01:59.119 GF series plates also do not have 00:02:01.84000:02:01.850 hangers simply tilt the plate as shown 00:02:04.96000:02:04.970 and remove larger uxb 800 plates are not 00:02:10.47900:02:10.489 secured by hangers and the following 00:02:12.55000:02:12.560 procedures should be followed for their 00:02:14.41000:02:14.420 removal remove the short sectional guide 00:02:17.80000:02:17.810 bar which is bolted to the bottom of the 00:02:19.93000:02:19.940 upper I beam slide the plate to be 00:02:22.69000:02:22.700 removed to the slot lower the plate tilt 00:02:26.11000:02:26.120 it and remove the plate from the frame 00:02:28.71000:02:28.720 there are three short sections on each 00:02:31.39000:02:31.400 guide bar to facilitate plate removal
Office location
Engineering company LOTUS®
Russia, Ekaterinburg, Lunacharskogo street, 240/12